Lowbed

Fliegl SDS 470 T mit Radmulden

Customized Transport Solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements.

Chassis, Low-loader Semi-trailer
Steel welded construction, kingpin plate with 2 replaceable kingpins and 2 kingpin positions
24 tons, 2-speed landing gear, single-side operation, with straight lower part, without lateral support
Foldable rear support
2 chock blocks with holder
Aluminum side protection
Fender fairings in front of and behind the axle assembly
1st pair of wheel recesses integrated into the gooseneck area in the low-bed section, angled for easy entry. Length at the bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess.
2nd pair of wheel recesses between axles A and B. Length at the bottom approx. 350 mm, depth approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess.
If wheel loaders are to be transported and the overall height needs to be checked, please provide the technical data sheet for the wheel loader models with detailed specifications (if the overall height is exceeded).
Wheel recess cover, retractable from the main frame, with wood inserts.
Extensions retractable to 3,000 mm (not in the rear slope and not in the wheel recesses at the bottom)
Storage compartment for timber planks on the gooseneck, across the front
Timber planks, 70 mm, for extension to 3000 mm
Tie-down points for low-loader
2 pairs of ring-type tie-down points, 5 tons each, at the front on the gooseneck
11 pairs of tie-down eyes integrated into the top and side of the outer frame, 10 tons each
2 x on the gooseneck, 9 x distributed in the low-loader area, first tie-down point 250 mm from the front and last max. 250 mm from the rear, spacing between tie-down points not greater than 1100 mm
8 pairs of stake pockets integrated into the outer frame, inner dimensions 70 x 40 mm, or, instead of stake pockets, 5-ton ring-type tie-down points embedded in the floor
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-aligned to reduce tire wear and fuel consumption
Air suspension
Wheels and Tires
235 / 75 R 17.5
Fgjdoi Ri Hcopfx Acwed
Manufacturer's choice
Steel rims in twin configuration, factory silver
Braking System
2-line pneumatic braking system
Spring-loaded parking brake
EBS, Electronic Braking System with EBS socket at the front, without connection cable
2 keyed coupling heads at the front
With raise and lower valve
Axle load detection via EBS-CAN bus signal, for display on the dashboard in the cab; truck must be suitably pre-equipped.
Vehicle - Driving Stability System
Electrical System
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front
2 white/red marker lights at the rear
2 x 7-pole keyed sockets at the front
1 x LED rotating beacon with holder, switched via side lights
2 pairs of warning signs, double LED illuminated and retractable to 3,000 mm, detachable with connector
Floor
Gooseneck with steel/non-slip steel plate
Storage box integrated into the access slope to the gooseneck
Then with 70 mm softwood floor, in the wheel recesses at the bottom and in the wheel well area, steel/non-slip steel plate
Low-loader platform including rear slope, 9,100 mm
Ramps
Steel ramps, 2,800 mm long, 750 mm wide, side-shiftable
Additional ramp securing at the bottom.

Огласот е автоматски преведен. Можно е да има грешки во преводот.