Lowbed

Fliegl VTS 400 RR

Further information
Chassis low loader trailer
Welded steel construction
Turntable with powerful ball bearing slewing ring
Folding rear support
2 wheel chocks with holder
Aluminum side bumpers
Rear splash guards across the entire width
Quarter-shell mudguards in front of 1st axle
Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope
1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm
1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess.
Wheel well cover can be pulled out from the main frame, with wooden inserts.
Distance from main frame beam to beam outside approx. 1280 mm (wheel well area)
Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm)
Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible
Wooden planks 70 mm for widening to 3000 mm
Low loader lashing eyes
1 pair of front lashing eyes recessed on offset, 5 tons each
Cedei Ri I Nepfx Aafjri
8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each
2 x at the front on the offset
6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm
5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets)
Trailer drawbar Turntable
Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye
Axles + suspension
SAF drum brake axles
Axle/chassis laser-measured Reduction in tire wear and fuel consumption
Air suspension with lift & lower valve can be operated separately at the front and rear
Wheels and tires
235 / 75 R 17,5
at the manufacturer's choice
Twin steel rims, factory silver
Brake system
2-line compressed air brake system
Spring-loaded parking brake
Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer
Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales)
Vehicle - driving stability system
Duomatic connection at the front, with connecting cable to the truck,
EBS, electronic braking system with EBS plug at the front, with connecting cable
Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Electrical system
24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given)
2 white front position lights in LED
2 white/red rear lane departure ligh

Огласот е автоматски преведен. Можно е да има грешки во преводот.